Service Parts - Gate Op

Showing 1–100 of 4000 results

• 

  .625 DIA, Heyco strain relief

• 

  “B” Motor Brushes

• 

  “E” Motor Brushes

• 

  (D) Drive Wheel 6″ Winter Sand

• 

  (D) Fuse 1.5 amp

• 

  (D) MGC Basic Controller

• 

  (D)5FT Led (12VDC)

• 

  (D)DOT Red/White tape – two 1″ strips –

• 

  (D)Installation Kit, Complete

• 

  [OLD LEGACY 1.0MM CONNECTOR] – 14.5ft LE

• 

  [OLD LEGACY 1.0MM CONNECTOR] – 25ft LED

• 

  #18 Key (set of 2)

• 

  #18 Lock for MIB Hood and MIB/MBE Door

• 

  #19 Key (set of 2)

• 

  #19 MicroDrive Lockset with 2 keys

• 

  #25 Chain

• 

  #35 Limit Chain

• 

  #35 Limit Chain Eagle I & II

• 

  #40 Chain Corrosion Resistant Kit, 30 ft

• 

  #40 limit chain for 2000 FR

• 

  #41 Chain-per foot

• 

  #41 Chain, for Patriot RSL Gear Motor

• 

  #50 3/8-inch Flange Bearing

• 

  #50 idler sprocket

• 

  #50 idler sprocket

• 

  #70 Gear Box Assy

• 

  1 – 1/4″ flange bearing

• 

  1 HP BRUSHLESS DC MOTOR (750W)

• 

  1 HP DC Motor for an SL150

• 

  1 HP DUAL CAP AC MOTOR

• 

  1 inch sprocket for tandem kit

• 

  1 pre-cut Spare LED Strip for 10 foot

• 

  1 Pre-Cut Spare LED Strip for 12ft

• 

  1″ Pillow Block Bearing

• 

  1″ Roller Shaft Kit-SwingRiser

• 

  1″ Roller Upgrade Shaft Kit-SwingRiser

• 

  1″ Sprocket 13 Teeth

• 

  1″ Sprocket 21 Teeth

• 

  1/2 HP AC MOTOR

• 

  1/2 HP BRUSHLESS DC MOTOR (500W)

• 

  1/2 HP DUAL CAP AC MOTOR

• 

  1/2 HP motor for the Eagle 1

• 

  1/2″ Chain Bolt, (1 PC)

• 

  1/2HP Motor

• 

  1/8 GAS BRASS CAPS+ BONDED SEALS (10

• 

  10 ft Alum Barrier Arm Octagonal

• 

  10 ft Articulating Alum Arm Octagonal

• 

  10 ft Protective-Padding for under Arm

• 

  10.5ft LED (24VDC) no wiring harnesses

• 

  100054 10010-1 KIT KEY CODE N.002 1 Piec

• 

  100ft Cable, Master/Second Communication

• 

  10UF Capacitor (220)

• 

  115V Relay and Base – Shadow Loop

• 

  12 ft Articulating Alum Arm Octagonal

• 

  120 VAC Receptacle

• 

  120V CSB XTREME CONTROL BOARD FOR MU36

• 

  120V Heater Kit-SlideDriver

• 

  120V KIT SCHEDA INVERTER PRO 36

• 

  120V THALIA P Transformer

• 

  12MM Flat Washer

• 

  12V actuator/motor

• 

  12V Relay and Base (Maglock)

• 

  14 pin terminal strip

• 

  14.5ft LED(24VDC) no wiring harnesses

• 

  14’ upper arm w/ light strip for M30

• 

  15 Amp Fuse

• 

  15 ft Protective-Padding for under Arm

• 

  15′ aluminum barrier arm (red/white stri

• 

  15Amp Circuit Breaker-SmartDC

• 

  15amp glass fuse

• 

  15ft LED [24VDC] – HIGH-BRIGHTNESS (wiri

• 

  16 x 18 120V FIBERGLASS PREWI

• 

  16” Adhesive Reflector

• 

  16/5 Conductor Wire -per ft

• 

  175-24′ SPEED CHANGE PULLEY KIT. TWO PUL

• 

  1hp Drive Wheels (2 pk)

• 

  1HP Motor for Eagle 200

• 

  1HP Motor for Eagle 200

• 

  1st Gen Carriage, Lead Screw / Hardware

• 

  1st gen Viking G5 Limit switch

• 

  2 ½” spacer bushing packet

• 

  2 Button Push Button Station

• 

  2 Conductor Cable -E4- per foot

• 

  2 Position Directional Valve

• 

  2 x 2 x 17 Mounting tube

• 

  2-Channel Loop Detector

• 

  2-spring set for the VPL-24

• 

  2.5 Gal Accumulator Bladder

• 

  2″ Motor Pulley

• 

  20 pack – Vibration Isolation Mounting

• 

  20:1 Gear Reducer

• 

  20′ Aluminum Barrier Arm, Octagonal

• 

  2000-2500# LARGE SPRING END-FRONT CABLE

• 

  2000-2500# LARGE SPRING END-REAR (ROD/AC

• 

  208/230VAC Catch Post Heater

• 

  208/230VAC Pivot Post Heater

• 

  208/240 VAC 3 phase pump motor

• 

  20amp glass fuse

• 

  20ft LED [24VDC] – HIGH-BRIGHTNESS

• 

  20ft LED [24VDC] (wiring harnesses avail